Mr. Handyman How To Guide
Now is the time for all good men and women to come to the aid of their neglected decks! Like many home maintenance efforts, the simple timely repairs save more difficult, time-consuming and expensive ones later. Like some other maintenance work, deck repairs can also be a matter of safety, such as when you secure a loose railing or replace a rotten stair tread. Fortunately, the basic carpentry skills and tools required make this project within reach of most homeowners. Giving the deck a thorough cleaning is the best place to start. Next, set nails and sand rough or splintering deck. Use a Cat's-Paw-type nail puller and pry bar to remove damaged decking. Also replace treads that are rotten or otherwise damaged. Secure posts that are inadequately nailed or screwed in place. When all cleaning and repairs are complete, treat your deck to a coat of water-repellent stain. Even pressure-treated wood requires such annual protection.
Before You Begin: Every spring, make a careful inspection of your deck to determine which repairs may be required. Are railings, especially those around stairs, solidly fastened? Is the surface splintered or covered with algae? Does any decking or framing need to be replaced? Make a list of all the work to be done and material needed. On a nice sunny weekend, gather or rent the necessary tools, including safety gear, such as goggles and kneepads.
Rent a pressure-washer for the day. You'll have so much fun cleaning the deck that you won't want to stop there. Walks, driveway, car ... but please, not the dog!
Scrub Deck: Start with a good cleaning. Scrub the decking surface until it's clean and free of slippery green slime (algae). Use a garden hose with power nozzle, and an old knife or similar tool to get out dirt and debris from between the cracks. Use one of the many commercial deck cleaners available according to instructions on the label. Deck restorers can be used in place of cleaners to restore the original color of the wood. They are sprayed and/or scrubbed on, and hosed off.
Secure Nails: As wood expands and contracts, nails may "pop" above the surface, presenting a tripping hazard. Use a hammer and nail set to drive them below the surface. Do this, too, if you plan to sand (next step). Raised nail heads will quickly turn your $2 sanding belt to shreds.
Sand Wood: Sand rough surfaces. Pay special attention to splintered areas and to handrails. Use a power sander, such as the belt sander shown here, with 80-grit paper. Large shard-like splinters follow the grain and sanding out may cut too deeply. Use a hammer and chisel to cut these spears off at the base and sand and rough edges.
Remove Damaged Wood: Cut out a section of a damaged board rather than replace the entire board. Use a jigsaw to crosscut the board adjacent to a joist. Cut a 2 x 4 block; bore clearance holes for two 3-in. no. 8 exterior screws; and secure it to the joist at the repair location. Cut a board to fit; and secure it to the nailer and any joists with screws.
Secure Boards: Use 3-in. no. 8 exterior wood screws and a drill-driver to secure 2x decking. Drill clearance holes (equal to screw diameter) through the decking only when attempting to draw down warped or cupped boards, and at the ends of boards to prevent splitting. If available, use the drill's torque setting to prevent snapping off screws due to too much force.
Repair Stairs: Cut through the middle of any damaged stair treads to remove it. Measure and cut new board. Treads may be set into a dado or nailed to a cleat attached to the side of a stair stringer. If there is a notched stringer in the center of a wider set of steps, use a nail puller. (Prying or banging may split the vulnerable stringer.)
Replace Tread: Cut a replacement tread and insert it into the dados in the stringers. If you have a pipe clamp, use it to draw the stringers tight against the edges of the tread before fastening it with three 2-1/2-in. no. 8 exterior decking screws. Do the same if cleats are employed, but make sure they are sound and securely screwed to the stringers.
Secure Railing: Nails and screws are inadequate to secure railing posts. If your older deck was built this way, bring it up to code. Use a spade drill bit and bore clearance holes through the post and perimeter joists and install two 5/16- or 3/8-in. through-bolts (length to suit, and with washers of both ends) at each post location, especially at any steps.
Tools and Materials:
Written by Roy Barnhart, home improvement expert, Fairfield, CT
Copyright © 2008 by Mr. Handyman of Puget Sound. All rights reserved.